Blue Cobalt Hits The Spot Grunge Cotton Wideback Fabric 3 4 Yard Pack Moda Fabrics Supplies

Start with the throw, not a universal rule

This guide works one example all the way through: a finished throw top that measures 60 inches by 72 inches. The goal is to find the backing size that quilt needs, check it in both orientations on a wideback, and convert the cut length to yardage you can order.

There is no universal backing allowance that fits every quilter, frame, and quilting method. Allowance is the extra backing needed beyond the top on each side for loading and quilting. Confirm the per-side amount with your own quilter before you calculate, and use that confirmed figure as your input. The example below uses one confirmed figure to show the arithmetic. If your quilter gives you a different figure, keep the same steps and replace that one number.

Step 1: Confirm the allowance per side

Suppose your quilter confirms 4 inches per side. That is an example input for this throw, not a rule for every quilt. Write down your own confirmed amount before you go further, because it changes both the required size and the yardage.

Required backing width equals the top width plus twice the per-side allowance. Required backing length equals the top length plus twice the per-side allowance.

Step 2: Work the required size for a 60 by 72 inch throw

With 4 inches per side: required width is 60 plus 8, which is 68 inches. Required length is 72 plus 8, which is 80 inches. So this throw needs a backing piece that is at least 68 inches by 80 inches.

Check the arithmetic independently: 60 + 4 + 4 = 68, and 72 + 4 + 4 = 80. If your confirmed allowance is different, redo those two additions first. Do not order until the required size reflects your quilter's figure.

Step 3: Compare both orientations

A wideback in this series is listed at a nominal width of 108 inches. Nominal width is the width named for the fabric, not a guaranteed usable width for your cut. Measure the usable width of your own piece, from the area you are willing to use, and plan from that measurement.

Orientation 1: 68-inch side across the width. Place the 68-inch required width across the wideback. It fits if your measured usable width is at least 68 inches. The cut length is then the other dimension, 80 inches.

Orientation 2: Rotate the layout. Place the 80-inch required length across the wideback instead. It fits only if your measured usable width is at least 80 inches. The cut length is then 68 inches. Rotating does not change the required backing size. It changes which dimension must fit across the width, and which dimension you pay for as cut length.

Step 4: Convert the cut length to yardage

Divide the cut length in inches by 36 to get yards, then round up to an amount you can actually order that still covers the full cut length.

Orientation 1: 80 divided by 36 is about 2.22 yards, so round up to 2.25 yards. That cut is 81 inches long, which covers the 80 inches required.

Orientation 2: 68 divided by 36 is about 1.89 yards, so round up to 2 yards. That cut is 72 inches long, which covers the 68 inches required.

For this throw, with this example allowance, rotating the layout uses less fabric, 2 yards instead of 2.25 yards, provided the 80-inch side truly fits within your measured usable width. If it does not fit, use Orientation 1, or plan a different backing. Never assume the nominal 108 inches is fully usable.

Final check before you order

Recheck three numbers: your top at 60 by 72 inches, your quilter-confirmed allowance per side, and your measured usable width. Confirm the required size, the orientation you chose, and the rounded yardage one more time. That short check replaces a universal rule with math that matches your quilt, your quilter, and your fabric.

Enjoying our quilting guides? Add Linda's as a preferred source on Google to see more of them in your search results: