Hey everyone, this is the 3yd Wide Cuddle Cut C390 Ash, our classic Solid Cuddle 3 minky plush fabric. Today you'll learn to make a bed runner, 26 by 72 inches.
Meet the Fabric First
It comes as a wide back pre-cut, 3 yards (108 inches long), at 88 to 90 inches wide. It is 100% polyester.
Ash is this cut's color name. Its surface is smooth and ultra-soft, beautiful and durable, with a versatile 3mm pile.
Why It Suits a Bed Runner
One Ash panel covers this runner's 26 by 72 inch top in one piece.
What You Will Need
- 3yd Wide Cuddle Cut C390 Ash fabric, for one top panel cut 28 by 74 inches
- Backing fabric, one panel cut 32 by 78 inches
- Batting, one piece cut 32 by 78 inches
- Binding fabric, in 2 1/2-inch strips joined into one strip at least 216 inches long
- Test-seam scraps, about 6 inches square, of Ash, backing, and batting
- All-purpose thread
- Sewing machine with a walking foot
- Size 90/14 stretch or ballpoint needle
- Rotary cutter, cutting mat, and a long ruler
- Long pins or quilting clips
- Fabric scissors and fabric marker or chalk
- Hand-sewing needle
- Seam ripper
Brief Steps to Make It
Step one, lay the Ash flat. Smooth it by hand.
Step two, mark the top panel at 28 by 74 inches, check square, then cut.
Step three, cut backing and batting at 32 by 78 inches each.
Step four, test first. Layer the listed scraps: backing right side down, batting, Ash pile side up. Sew with the walking foot, stitch length 3.0 to 3.5. Backstitch three stitches at the start and at the end.
Step five, layer the sandwich. Backing right side down, batting in the middle, Ash on top, pile side up, centered so batting and backing extend 2 inches per side.
Step six, pin baste, every 4 to 6 inches. Mark the 26 by 72 inch rectangle, centered, on top.
Step seven, quilt with the walking foot. Sew lines lengthwise, along the 74-inch direction, 4 inches apart across the 28-inch width. Start with one center line, then work outward to each side. Run every line from one raw short edge to the other. Do not stop inside the runner and do not backstitch. Those ends sit in the extra area step eight trims away, and the binding covers the rest.
If a line wanders, take it out with the seam ripper and sew it again, slower.
Step eight, trim all three layers on the marked lines, to 26 by 72 inches.
Step nine, bind it. Join your strips: lay two strips right sides together at a right angle. Sew diagonally corner to corner, backstitching three stitches at the start and at the end. Trim to 1/4 inch past that seam, finger-press it open. Repeat until the strip reaches at least 216 inches: the 196-inch edge, plus 20 for corners, joins, and tails. Fold it in half lengthwise, wrong sides together. Start halfway along one long edge, leaving a 12-inch tail, raw edges aligned with the front edge. Backstitch three stitches, then sew at a 1/4-inch seam allowance. That seam crosses every quilting line end, securing each one before the binding folds over it. Stop 12 inches before the point where your stitching began, leaving a gap and a second tail. Leave it unbackstitched; the tail join and gap closing finish it.
At each corner, stop 1/4 inch short and backstitch. Fold the strip up at a 45-degree angle, then down the next edge, fold flush with the sewn edge. Sew from the outer edge, same allowance, backstitching three stitches at the start.
Join the tails: lay the ending tail over the starting tail. Trim it where they overlap by 2 1/2 inches. Open both tails flat, right sides together at a right angle. Sew diagonally corner to corner, backstitching three stitches at the start and at the end. Trim to 1/4 inch, finger-press open, and refold. Sew the gap closed, same allowance, backstitching three stitches at each end. Fold the binding to the back, its folded edge covering the front stitching line by 1/8 inch. At each corner, fold one side down, then the other, for a diagonal fold. By machine: stitch in the ditch on the front, catching the back edge, backstitching three stitches at the start and the end. Or by hand: slipstitch it down with the hand-sewing needle, starting with a knotted thread. At the end, backstitch once, knot it, and bury the tail.
It does not have to be perfect.
Shop the 3yd Wide Cuddle Cut C390 Ash at Linda's Electric Quilters.



