Keys have a talent for sinking to the very bottom of a bag, usually when your hands are full and it is raining. A fabric key fob wristlet fixes that: a wide, padded loop you can slip over your wrist, grab at a glance, and spot by its bright fabric. It takes about twenty minutes, uses a strip of fabric you probably already have, and makes a genuinely useful holiday stocking stuffer.
What You'll Make
One padded fabric key fob wristlet, about 5 inches long folded, with metal fob hardware and a split ring for your keys. The wide fabric loop is soft, sturdy, and easy to hold. Make one to match your bag, then make a batch in different prints for teachers, coworkers, neighbors, and anyone who is hard to shop for. This is a confident-beginner project with only straight seams.
Materials
Seven of the eight items below (88%) come from Linda's — links included. The fob hardware comes from a craft store, explained below.
- Tula Pink Daydreamer Fat Quarter Bundle — quilting cotton for the strap; one fat quarter makes several fobs
- Pellon Lightweight Nonwoven Fusible Interfacing 20" White By The Yard — fused inside for body and strength
- The Gypsy Quilter Cotton Batting 10in x 10yds — a thin strip adds soft padding; batting scraps work perfectly
- 1100 Red Plum Aurifil Cotton 50wt Large Spool — for seams and topstitching; choose a color that suits your fabric
- Universal Needles Assorted - 10 count by Organ Needles — a fresh needle handles the layered strap cleanly
- Olfa Deluxe 45mm Rotary Cutter — for cutting long, straight strips on a mat
- Riley Blake Designs Quilty Clips — to hold the folded strap without pin holes
- One 1-inch key fob hardware set (the clamp with a split ring) — from most craft stores, hardware stores, or your local quilt shop; you will also need flat pliers to close it
Steps
- Cut your pieces. Cut one fabric strip 4 inches by 10 inches. Cut one interfacing strip the same size, and one batting strip about 1 inch by 10 inches.
- Fuse the interfacing. Following the manufacturer's directions, fuse the interfacing to the wrong side of the fabric strip with a hot iron. Let it cool flat.
- Fold the strap. Fold the long edges in to meet at the center, wrong sides together, and press. Slip the batting strip under one folded edge so it sits in the middle. Fold the strap in half lengthwise again so the raw edges are tucked inside. Clip along the length.
- Topstitch both edges. Sew close to each long edge, about 1/8 inch in, removing clips as you go. Backstitch at the start and end. This closes the strap and gives it a neat, finished look.
- Form the loop. Fold the strap in half, short ends together, so it makes a loop. Slide the two ends side by side into the open clamp of the fob hardware, pushing them in as far as they will go.
- Close the hardware. Wrap a scrap of fabric over the clamp to protect the metal, then squeeze it firmly shut with flat pliers, working from one side to the other until the teeth grip evenly. Give the strap a firm tug to check it is secure.
- Add your keys. Attach your keys to the split ring. Slip the loop over your wrist and you are done.
Tips
Batch smart: cut and fuse a whole fat quarter into strips, sew them all, then close all the hardware at once. Vary the length a little for different hands — 11 inches makes a roomier loop. For a lighter fob, skip the batting; for a sturdier one, keep it. If the clamp has sharp teeth, a folded piece of fabric inside the ends helps it grip without fraying. Always test the closed hardware with a strong tug before trusting it with your only set of keys.
Where to Get Everything
The fabric, interfacing, batting, thread, needles, rotary cutter, and clips linked above are all from Linda's Electric Quilters. The key fob hardware set is the one item to pick up elsewhere: look in the bag-making or jewelry aisle at most craft stores, at a hardware store, or ask your local quilt shop — it is usually sold in small multi-packs, which suits batch gift-making perfectly. Pliers from a basic home toolkit work fine.




